Abstract of Wireless Charging Of Mobile Phones Using Microwaves
With mobile phones becoming a basic part of life, the recharging of mobile phone batteries has always been a problem. The mobile phones vary in their talk time and battery standby according to their manufacture and batteries. All these phones irrespective of their manufacturer and batteries have to be put to recharge after the battery has drained out.
he main objective of this current proposal is to make the recharging of the mobile phones independent of their manufacturer and battery make. In this paper a new proposal has been made so as to make the recharging of the mobile phones is done automatically as you talk in your mobile phone! This is done by use of microwaves. The microwave signal is transmitted from the transmitter along with the message signal using special kind of antennas called slotted wave guide antenna at a frequency is 2.45 GHz.
There are minimal additions, which have to be made in the mobile handsets, which are the addition of a sensor, a Rectenna, and a filter. With the above setup, the need for separate chargers for mobile phones is eliminated and makes charging universal. Thus the more you talk, the more is your mobile phone charged! With this proposal the manufacturers would be able to remove the talk time and battery stand by from their phone specifications.
he main objective of this current proposal is to make the recharging of the mobile phones independent of their manufacturer and battery make. In this paper a new proposal has been made so as to make the recharging of the mobile phones is done automatically as you talk in your mobile phone! This is done by use of microwaves. The microwave signal is transmitted from the transmitter along with the message signal using special kind of antennas called slotted wave guide antenna at a frequency is 2.45 GHz.
There are minimal additions, which have to be made in the mobile handsets, which are the addition of a sensor, a Rectenna, and a filter. With the above setup, the need for separate chargers for mobile phones is eliminated and makes charging universal. Thus the more you talk, the more is your mobile phone charged! With this proposal the manufacturers would be able to remove the talk time and battery stand by from their phone specifications.
Introduction of Wireless Charging Of Mobile Phones Using Microwaves :
The basic addition to the mobile phone is going to be the rectenna. A rectenna is a rectifying antenna, a special type of antenna that is used to directly convert microwave energy into DC electricity.
Its elements are usually arranged in a mesh pattern, giving it a distinct appearance from most antennae. A simple rectenna can be constructed from a Schottky diode placed between antenna dipoles. The diode rectifies the current induced in the antenna by the microwaves.
Rectenna are highly efficient at converting microwave energy to electricity. In laboratory environments, efficiencies above 90% have been observed with regularity. Some experimentation has been done with inverse rectenna, converting electricity into microwave energy, but efficiencies are much lower--only in the area of 1%. With the advent of nanotechnology and MEMS the size of these devices can be brought down to molecular level.
It has been theorized that similar devices, scaled down to the proportions used in nanotechnology, could be used to convert light into electricity at much greater efficiencies than what is currently possible with solar cells. This type of device is called an optical rectenna.
Theoretically, high efficiencies can be maintained as the device shrinks, but experiments funded by the United States National Renewable energy Laboratory have so far only obtained roughly 1% efficiency while using infrared light. Another important part of our receiver circuitry is a simple sensor.
Its elements are usually arranged in a mesh pattern, giving it a distinct appearance from most antennae. A simple rectenna can be constructed from a Schottky diode placed between antenna dipoles. The diode rectifies the current induced in the antenna by the microwaves.
Rectenna are highly efficient at converting microwave energy to electricity. In laboratory environments, efficiencies above 90% have been observed with regularity. Some experimentation has been done with inverse rectenna, converting electricity into microwave energy, but efficiencies are much lower--only in the area of 1%. With the advent of nanotechnology and MEMS the size of these devices can be brought down to molecular level.
It has been theorized that similar devices, scaled down to the proportions used in nanotechnology, could be used to convert light into electricity at much greater efficiencies than what is currently possible with solar cells. This type of device is called an optical rectenna.
Theoretically, high efficiencies can be maintained as the device shrinks, but experiments funded by the United States National Renewable energy Laboratory have so far only obtained roughly 1% efficiency while using infrared light. Another important part of our receiver circuitry is a simple sensor.
Receiver Design :
The diode rectifies the current induced in the antenna by the microwaves. Rectenna are highly efficient at converting microwave energy to electricity.
In laboratory environments, efficiencies above 90% have been observed with regularity. In future rectennass will be used to generate large-scale power from microwave beams delivered from orbiting SPS satellites.
The sensor circuitry is a simple circuit, which detects if the mobile phone receives any message signal. This is required, as the phone has to be charged as long as the user is talking. Thus a simple F to V converter would serve our purpose. In India the operating frequency of the mobile phone operators is generally 900MHz or 1800MHz for the GSM system for mobile communication.
No comments:
Post a Comment